The Electronics Starter Kit (or ESK, as we like to call it) is the Kit containing essentials to get started learning micro-controller based electronics with the help of Development Board. The ESK includes a total of 150+ components from 40 different categories.
Development Board Included: Arduino Uno R3
DIY Kit Included: BreadBoard Power Supply Kit v2.0
The BreadBoard Power Supply Kit v2.0 is a Learn to Solder Do-It-Yourself Kit. After it is fully assembled, it can easily connect to the power rails of a standard 830 tie-point Bread Board. BBPS v2.0 takes its input from a standard wall adapter supplying 6V - 12V into the Vin Port of the PCB through DC Jack or Screw Terminal and provides a regulated 3.3V or 5V output as required by the user. The PCB is fully labeled and includes names and values of all the components needed.
- By default, Arduino Uno R3 board and mini BreadBoard are included. You may change these options as per your choice.
- The Electronics Starter Kit comes with all the components that you need to get started into the world of Electronics.
- All the necessary Open Source Softwares like Arduino IDE, Processing, Wiring and Fritzing may be downloaded from the respective websites.
- 1x Development Board (As per choice)
- 1x Do It Yourself Kit: BreadBoard Power Supply Kit v2.0
- 1x USB Cable A to B/micro-B/mini-B/OTG (As per Development Board)
- 1x BreadBoard (As per choice)
- 1x Kester Solder Wire - Lead Free - 0.5 mm Diameter (Sn96.5+Ag3.0+Cu0.5) - 10 cm approx. length
- 20x Clear LEDs - Super Bright (Assorted)
- 5x Jumper Wires - Male to Male - 6”
- 5x Jumper Wires - Male to Male - 12”
- 5x Jumper Wires - Male to Female - 6”
- 5x Jumper Wires - Male to Female - 12”
- 5x Jumper Wires - Female to Female - 6”
- 2x Seven-Segment Display - Common Anode - Example Code
- 1x Shift Register - 74HC595 (ST Microelectronics)
- 2x MOSFET 100 V 33 A - IRF540N (International Rectifier)
- 1x Trim Pot - 10 K (Bourns)
- 1x Piezo Buzzer - 2 kHz
- 10x Metal Film Resistor - 100 Ohm
- 10x Carbon Film Resistor - 330 Ohm
- 10x Metal Film Resistor - 1 KOhm
10x Metal Film Resistor - 4.7 KOhm(Updated on: 13-02-2015)
- 10x Carbon Film Resistor - 10 KOhm
- 10x Diode IN4007 (Reverse Protection)
- 4x Electrolytic Capacitor - 100 uF/25V
- 4x Electrolytic Capacitor - 10 uF/63V
- 10x Ceramic Capacitor - 0.1 uF
- 4x Ceramic Capacitor - 22 pF
- 4x NPN Transistor - BC547
- 1x Light Dependent Resistor (LDR)
- 1x Negative Temperature Coefficient (NTC) Thermistor - 1 K/10 K (as per availability)
- 1x InfraRed LED Tx-Rx Pair - 3 mm/5 mm (as per availability) - Example Code
- 1x Screw Terminal - 5mm - 2 Pins
- 4x Momentary Push Button Switch - 4 Pins
- 2x On-Off Switch - 6 Pins
2x Selection Jumper(Updated on: 13-02-2015)
- 1x Motor Driver IC - L293D (Texas Instruments)
- 1x Toy Motor - DC
1x Propeller for Toy Motor(Updated on: 13-02-2015)
- Additional Information
Processor No Architecture No Clock Speed No Digital Pins No Analog Pins No PWM Pins No Hardware UART No Programming Interface No Flash Memory No Operating Voltage No Power Output No Antenna No Range (Indoor/Urban) No Range (Outdoor/RF Line of Sight) No Channel Capacity No Frequency No Transmit Current @ 3.3V No
Customer Reviews 1 item(s)
- Excellent Starter Kit
- Received the product in two days, and I am fully satisfied with the contents.